top of page

100MM WALL VENT KIT (BROWN)

This wall vent kit suit any 100mm wall extractor fan. A perfect way to complete your installation

 

The vent kit comes complete with an external wall grille and a telescopic liner. The telescopic liner makes it easy to fit, with no messy cutting required.

 

Telescopic liner suits wall thicknesses from 225mm up to 390mm

100MM WALL VENT KIT (WHITE)

This wall vent kit suit any 100mm wall extractor fan. A perfect way to complete your installation

 

The wall vent kit comes complete with an external wall grille and a telescopic liner. The telescopic liner makes it easy to fit, with no messy cutting required.

 

Telescopic liner suits wall thicknesses from 225mm up to 390mm

150MM WALL VENT KIT (BROWN)

This wall vent kit suit any 150mm wall extractor fan. A perfect way to complete your installation

 

The wall vent kit comes complete with an external wall grille and a telescopic liner. The telescopic liner makes it easy to fit, with no messy cutting required.

 

Telescopic liner suits wall thicknesses from 225mm up to 390mm

150MM WALL VENT KIT (WHITE)

This wall vent kit suit any 150mm wall extractor fan. A perfect way to complete your installation

 

The wall vent kit comes complete with an external wall grille and a telescopic liner. The telescopic liner makes it easy to fit, with no messy cutting required.

 

Telescopic liner suits wall thicknesses from 225mm up to 390mm

315MM DIA FLANGE

315mm dia Flange used to bolt directly to the Fan, as part of a full ancillary package or for the fan to mount inline in ducting

 

Can also be used to fix directly to a Silencer

 

Can also be used to fix directly to ducting

 

Hot dipped Galvanised after manufacture

Extract fan ESC50014/ZAC500-41

Manufactured by Ziehl Abegg and distributed by Vent Axia and Systemair, this is probably the most popular short cased axial on the market today. Ziehl Abegg are one of, if not the biggest external rotor motor manufacturers in the world, they have over 100 years of engineering experience behind them, which gives you the confidence. If a low cost painted finish fan is your choice this is among the best available.

  • Supplied fully assembled
  • ​
  • Fully speed controllable
  • Can be used in any non hazardous environment
  • Suitable to run in temperatures from -40°C to up to 70°C in some instances
  • Low to medium air volumes
  • Low to medium static pressures
  • Available sizes 315mm – 630mm from stock
  • 710mm – 1000mm check for availability
  • Tough epoxy paint finish
  • Die cast aluminium impellers (the bit that goes around)
  • Motor class F insulation with protection to IP54
  • All fans reversible for supply or extractv

Extract Fan ESP31514/ ZAP315-41

Manufactured by Ziehl Abegg and distributed by Vent Axia and Systemair, this is probably one of the most popular plate mounted axials on the market today. Ziehl Abegg are one of, if not the biggest external rotor motor manufacturers in the world, they have over 100 years of engineering experience behind them, which gives you the confidence. If a low cost painted finish fan is your choice this is among the best available.

 

Supplied fully assembled

Fully speed controllable

Can be used in any non hazardous environment

Suitable to run in temperatures from -40°C to up to 70°C in some instances

Low to medium air volumes

Low to medium static pressures

Available sizes 315mm – 630mm from stock

710mm – 1000mm check for availability

Tough epoxy paint finish

Die cast aluminium impellers (the bit that goes around)

Motor class F insulation with protection to IP54

All fans reversible for supply or extract

Extract fan ESP45014 ZAP450-41

Manufactured by Ziehl Abegg and distributed by Vent Axia and Systemair, this is probably one of the most popular plate mounted axials on the market today. Ziehl Abegg are one of, if not the biggest external rotor motor manufacturers in the world, they have over 100 years of engineering experience behind them, which gives you the confidence. If a low cost painted finish fan is your choice this is among the best available.

  • Supplied fully assembled
  • Fully speed controllable
  • Can be used in any non hazardous environment
  • Suitable to run in temperatures from -40°C to up to 70°C in some instances
  • Low to medium air volumes
  • Low to medium static pressures
  • Available sizes 315mm – 630mm from stock
  • 710mm – 1000mm check for availability
  • Tough epoxy paint finish
  • Die cast aluminium impellers (the bit that goes around)
  • Motor class F insulation with protection to IP54
  • All fans reversible for supply or extract

Bathroom Shower Kitchen Toilet

High output tube extract fan with overrun timer. Ducted bath/shower kit, consists of a Minivent IP44 In-Line fan, a ventilation kit consisting of a white ceiling grille and spigot, external louvre for soffit or wall mounting plus 3 meters of flexible duct. The duct should be cut to size, the bend radius should be kept to a maximum to provide the best fan performance

Important Note - Building regulations state "in a room with no openable window, an intermittent extract fan should be used with a run on facility set to a minimum of 15 minutes."

PIR 4 Passive Infrared Sensor

c/w run on timer settable between 5 - 30 minutes

 

c/w run on timer settable between 5 - 30 minutes

A Wall or Ceiling mounted movement detector for use with any of our Domestic mains voltage fans.

 

This little single gang size sensor is a great little energy saving device. The fan will only run when the sensor senses movement.

 

Example

 

Fit this in a bathroom and the fan will only run when someone is in the bathroom.

 

Fitted as standard is a run on timer adjustable for 5 - 30 minutes, so the fan will run for as long as want up to 30 minutes after you've left the room

 

Important Note - Building regulations state "in a room with no openable window, an intermittent extract fan should be used with a run on facility set to a minimum of 15 minutes."

SP5025 Vent Axia / Roof Units Electronic Fan Speed Controller

The Roof Units SP range of electronic fan speed controllers manufactured by Vent Axia. This range of fan speed controllers can be used with any Fan / Motor which is single phase – 240 volts and speed controllable using either 2 or 3 wire control (+earth).

 

SP5001 suitable for a maximum full load of 1.7 amp

SP5025 suitable for a maximum full load of 3 amps

SP5050 suitable for a maximum full load of 6 amps (up to 7 amps when used as 3 wire (+earth))

SP5010 suitable for a maximum full load of 10amps

The SP range of fan speed controllers can be used with any manufacturers fans / motors which are single phase and suitable for speed control via 2 or 3 wires (+earth) including

 

Flakt Woods

Ziehl Abegg

Elta

Helios

Solar and Palau

Nuaire

Not sure if your fan is suitable? just ask and we can check for you

Wall Ventilation External Gravity Shutter (100mm)

terminates 100mm dia rigid or flexible ducting

 

terminates 100mm dia rigid or flexible ducting

This plastic external gravity shutter is a cost effective solution when you need to terminate a hole in an external or internal wall.

 

This shutter is an ideal fuss free solution, when only the shutter is required or when you need to customize your wall vent kit (usually when a standard wall sleeve isn’t long enough for the thickness of wall or cavity it’s going through)

 

Available sizes

 

To suit 100mm fan

To suit 150mm fan

Available colours

 

White

Brown

Please reload

315MM DIA FLANGE

suits any manufacturer of fans

315mm dia Flange used to bolt directly to any manufacturer of Fans, as part of a full ancillary package or for the fan to mount inline in ducting.

 

This flange is unique because it is designed to fix to UK and European PCD detail, meaning this flange will fix to any manufacturers fans

 

Can also be used to fix directly to a Silencer

 

Can also be used to fix directly to ducting

 

Manufactured from pre Galvanised sheet

315MM FLEXIBLE CONNECTION

315mm Flexible connection, used to fit to Flanges (with spigots), Silencers (with spigots) or spiral ducting.

 

A flexible connection is used to isolate the fan from the system to prevent vibration transfer and helps minimise noise transfer through fixings or structures.

 

It can also be used to simplify installation by bridging any small gaps between sections of the installation, for example the gap between a fan and the ductwork

315MM LOUVRE SHUTTER

A Louvre Shutter is a gravity type shutter which can be used to terminate and weather extract systems. When the fan is running the plastic blades will open allowing the air to be extracted from the system, and when the fan is not running will be closed, this helps to prevent back draughts and water ingress

 

The shutter is commonly used to terminate systems where a plate mounted fan has been fitted internally, and used for extraction

 

Louvre shutters are usually either mounted to an external wall or at the end of a galvanised box to terminate an extract system

 

This Louvre shutter can only be used on EXTRACT systems, for SUPPLY systems please contact us direct, by any means you feel comfortable with and we will advise what should be used to suit your application

355MM DIA FLANGE

355mm dia Flange used to bolt directly to the Fan, as part of a full ancillary package or for the fan to mount inline in ducting

 

Can also be used to fix directly to a Silencer

 

Can also be used to fix directly to ducting

 

Hot dipped Galvanised after manufacture

355MM DIA FLANGE

suits any manufacturer of fans

mm dia Flange used to bolt directly to any manufacturer of Fans, as part of a full ancillary package or for the fan to mount inline in ducting.

 

This flange is unique because it is designed to fix to UK and European PCD detail, meaning this flange will fix to any manufacturers fans

 

Can also be used to fix directly to a Silencer

 

Can also be used to fix directly to ducting

 

Manufactured from pre Galvanised sheet

355MM DIA FLEXIBLE CONNECTION

355mm Flexible connection, used to fit to Flanges (with spigots), Silencers (with spigots) or spiral ducting.

A flexible connection is used to isolate the fan from the system to prevent vibration transfer and helps minimise noise transfer through fixings or structures.

It can also be used to simplify installation by bridging any small gaps between sections of the installation, for example the gap between a fan and the ductwork

Industrial electronic fan speed controllers

The Vent-Axia Industrial range of electronic fan speed controllers manufactured by Vent-Axia. This range of fan speed controllers can be used with any Fan / Motor which is single phase – 240 volts and speed controllable using either 2 or 3 wire control (+earth).

  • W10303102M suitable for a maximum full load of 2.5 amps
  • 10303103A suitable for a maximum full load of 3 amps
  • 10303106A suitable for a maximum full load of 6 amps
  • 10303110A suitable for a maximum full load of 10 amps

The Vent-Axia Industrial range of fan speed controllers can be used with any manufacturers fans / motors which are single phase and suitable for speed control via 2 or 3 wires (+earth) including

  • Flakt Woods
  • Ziehl Abegg
  • Elta
  • Helios
  • Solar and Palau
  • Nuaire
  • Systemair
  • Vent-Axia
  • Roof Units

Not sure if your fan is suitable? just ask and we can check for you

Extract fan ESC56014 /ZAC560-41

Manufactured by Ziehl Abegg and distributed by Vent Axia and Systemair, this is probably the most popular short cased axial on the market today. Ziehl Abegg are one of, if not the biggest external rotor motor manufacturers in the world, they have over 100 years of engineering experience behind them, which gives you the confidence. If a low cost painted finish fan is your choice this is among the best available.

 

Supplied fully assembled

Fully speed controllable

Can be used in any non hazardous environment

Suitable to run in temperatures from -40°C to up to 70°C in some instances

Low to medium air volumes

Low to medium static pressures

Available sizes 315mm – 630mm from stock

710mm – 1000mm check for availability

Tough epoxy paint finish

Die cast aluminium impellers (the bit that goes around)

Motor class F insulation with protection to IP54

All fans reversible for supply or extract

Extract fan ESP35514/ ZAP350-41

Manufactured by Ziehl Abegg and distributed by Vent Axia and Systemair, this is probably one of the most popular plate mounted axials on the market today. Ziehl Abegg are one of, if not the biggest external rotor motor manufacturers in the world, they have over 100 years of engineering experience behind them, which gives you the confidence. If a low cost painted finish fan is your choice this is among the best available.

  • Supplied fully assembled

  • Fully speed controllable

  • Can be used in any non hazardous environment

  • Suitable to run in temperatures from -40°C to up to 70°C in some instances

  • Low to medium air volumes

  • Low to medium static pressures

  • Available sizes 315mm – 630mm from stock

  • 710mm – 1000mm check for availability

  • Tough epoxy paint finish

  • Die cast aluminium impellers (the bit that goes around)

  • Motor class F insulation with protection to IP54

  • All fans reversible for supply or extract

Extractor Fan ZAP500-41

Manufactured by Ziehl Abegg and distributed by Vent Axia and Systemair, this is probably one of the most popular plate mounted axials on the market today. Ziehl Abegg are one of, if not the biggest external rotor motor manufacturers in the world, they have over 100 years of engineering experience behind them, which gives you the confidence. If a low cost painted finish fan is your choice this is among the best available.

  • Supplied fully assembled

  • Fully speed controllable

  • Can be used in any non hazardous environment

  • Suitable to run in temperatures from -40°C to up to 70°C in some instances

  • Low to medium air volumes

  • Low to medium static pressures

  • Available sizes 315mm – 630mm from stock

  • 710mm – 1000mm check for availability

  • Tough epoxy paint finish

  • Die cast aluminium impellers (the bit that goes around)

  • Motor class F insulation with protection to IP54

  • All fans reversible for supply or extract

Vent Axia 10303103A fan speed controller

The Vent-Axia Industrial range of electronic fan speed controllers manufactured by Vent-Axia. This range of fan speed controllers can be used with any Fan / Motor which is single phase – 240 volts and speed controllable using either 2 or 3 wire control (+earth).

 

W10303102M suitable for a maximum full load of 2.5 amps

10303103A suitable for a maximum full load of 3 amps

10303106A suitable for a maximum full load of 6 amps

10303110A suitable for a maximum full load of 10 amps

The Vent-Axia Industrial range of fan speed controllers can be used with any manufacturers fans / motors which are single phase and suitable for speed control via 2 or 3 wires (+earth) including

 

Flakt Woods

Ziehl Abegg

Elta

Helios

Solar and Palau

Nuaire

Systemair

Vent-Axia

Roof Units

Not sure if your fan is suitable? just ask and we can check for you

Vent Axia 10303106A fan speed controller

The Vent-Axia Industrial range of electronic fan speed controllers manufactured by Vent-Axia. This range of fan speed controllers can be used with any Fan / Motor which is single phase – 240 volts and speed controllable using either 2 or 3 wire control (+earth).

 

W10303102M suitable for a maximum full load of 2.5 amps

10303103A suitable for a maximum full load of 3 amps

10303106A suitable for a maximum full load of 6 amps

10303110A suitable for a maximum full load of 10 amps

The Vent-Axia Industrial range of fan speed controllers can be used with any manufacturers fans / motors which are single phase and suitable for speed control via 2 or 3 wires (+earth) including

 

Flakt Woods

Ziehl Abegg

Elta

Helios

Solar and Palau

Nuaire

Systemair

Vent-Axia

Roof Units

Not sure if your fan is suitable? just ask and we can check for you

BAS100SLB Bathroom Kitchen wall mounted extractor fan

c/w integral backdraught shutter

 

c/w integral backdraught shutter

Bathroom, Toilet, Kitchen and Cloakroom Extractor fan

 

Vent Axia’s BASICS range. Low cost, but top quality, from what we consider to be the most famous brand name in residential and commercial ventilation equipment in the UK. No matter which range of fans you buy, when they have the Vent Axia badge, you know you have made the right choice.

 

We recommend this range where you need low cost with great looks, an acceptable noise level and high quality.

 

The Basics range are suitable for use in Bathroom’s, Toilets, Kitchens and Cloakrooms, the range are almost flush mounted, with the fan only protruding 15mm off the wall. They can be mounted on either a wall or panel, (appropriate Fixing Kit may be required, please check our related products below) we only supply versions with a back draught shutter fitted, they can be wired to run via a light switch or separate remote switch.

 

Important Note - Building regulations state "in a room with no openable window, an intermittent extract fan should be used with a run on facility set to a minimum of 15 minutes."

 

The whole range is Part F compliant

IP44 rated 100mm range

IPx4 rated 150mm range

check regulations here

Please reload

400MM DIA FLANGE

400mm dia Flange used to bolt directly to the Fan, as part of a full ancillary package or for the fan to mount inline in ducting

 

Can also be used to fix directly to a Silencer

 

Can also be used to fix directly to ducting

 

Hot dipped Galvanised after manufacture

400MM FLEXIBLE CONNECTION

400mm Flexible connection, used to fit to Flanges (with spigots), Silencers (with spigots) or spiral ducting.

A flexible connection is used to isolate the fan from the system to prevent vibration transfer and helps minimise noise transfer through fixings or structures.

It can also be used to simplify installation by bridging any small gaps between sections of the installation, for example the gap between a fan and the ductwork

450MM LOUVRE SHUTTER

A Louvre Shutter is a gravity type shutter which can be used to terminate and weather extract systems. When the fan is running the plastic blades will open allowing the air to be extracted from the system, and when the fan is not running will be closed, this helps to prevent back draughts and water ingress

The shutter is commonly used to terminate systems where a plate mounted fan has been fitted internally, and used for extraction

Louvre shutters are usually either mounted to an external wall or at the end of a galvanised box to terminate an extract system

This Louvre shutter can only be used on EXTRACT systems, for SUPPLY systems please contact us direct, by any means you feel comfortable with and we will advise what should be used to suit your application

500MM DIA FLANGE

500mm dia Flange used to bolt directly to the Fan, as part of a full ancillary package or for the fan to mount inline in ducting

 

Can also be used to fix directly to a Silencer

 

Can also be used to fix directly to ducting

 

Hot dipped Galvanised after manufacture

500MM FLEXIBLE CONNECTION

500mm Flexible connection, used to fit to Flanges (with spigots), Silencers (with spigots) or spiral ducting.

 

A flexible connection is used to isolate the fan from the system to prevent vibration transfer and helps minimise noise transfer through fixings or structures.

 

It can also be used to simplify installation by bridging any small gaps between sections of the installation, for example the gap between a fan and the ductwork

560MM FLEXIBLE CONNECTION

560mm Flexible connection, used to fit to Flanges (with spigots), Silencers (with spigots) or spiral ducting.

 

A flexible connection is used to isolate the fan from the system to prevent vibration transfer and helps minimise noise transfer through fixings or structures.

 

It can also be used to simplify installation by bridging any small gaps between sections of the installation, for example the gap between a fan and the ductwork

.

630MM DIA FLANGE

630mm dia Flange used to bolt directly to the Fan, as part of a full ancillary package or for the fan to mount inline in ducting

 

Can also be used to fix directly to a Silencer

 

Can also be used to fix directly to ducting

 

Hot dipped Galvanised after manufacture

630MM FLEXIBLE CONNECTION

630mm Flexible connection, used to fit to Flanges (with spigots), Silencers (with spigots) or spiral ducting.

 

A flexible connection is used to isolate the fan from the system to prevent vibration transfer and helps minimise noise transfer through fixings or structures.

 

It can also be used to simplify installation by bridging any small gaps between sections of the installation, for example the gap between a fan and the ductwork

630MM LOUVRE SHUTTER

A Louvre Shutter is a gravity type shutter which can be used to terminate and weather extract systems. When the fan is running the plastic blades will open allowing the air to be extracted from the system, and when the fan is not running will be closed, this helps to prevent back draughts and water ingress

The shutter is commonly used to terminate systems where a plate mounted fan has been fitted internally, and used for extraction

Louvre shutters are usually either mounted to an external wall or at the end of a galvanised box to terminate an extract system

This Louvre shutter can only be used on EXTRACT systems, for SUPPLY systems please contact us direct, by any means you feel comfortable with and we will advise what should be used to suit your application

710MM DIA FLANGE

710mm dia Flange used to bolt directly to the Fan, as part of a full ancillary package or for the fan to mount inline in ducting

 

Can also be used to fix directly to a Silencer

 

Can also be used to fix directly to ducting

 

Hot dipped Galvanised after manufacture

710MM FLEXIBLE CONNECTION

710mm Flexible connection, used to fit to Flanges (with spigots), Silencers (with spigots) or spiral ducting.

 

A flexible connection is used to isolate the fan from the system to prevent vibration transfer and helps minimise noise transfer through fixings or structures.

 

It can also be used to simplify installation by bridging any small gaps between sections of the installation, for example the gap between a fan and the ductwork

710MM LOUVRE SHUTTER

A Louvre Shutter is a gravity type shutter which can be used to terminate and weather extract systems. When the fan is running the plastic blades will open allowing the air to be extracted from the system, and when the fan is not running will be closed, this helps to prevent back draughts and water ingress

 

The shutter is commonly used to terminate systems where a plate mounted fan has been fitted internally, and used for extraction

 

Louvre shutters are usually either mounted to an external wall or at the end of a galvanised box to terminate an extract system

 

This Louvre shutter can only be used on EXTRACT systems, for SUPPLY systems please contact us direct, by any means you feel comfortable with and we will advise what should be used to suit your application

ESC63014 / ZAC630-41

Manufactured by Ziehl Abegg and distributed by Vent Axia and Systemair, this is probably the most popular short cased axial on the market today. Ziehl Abegg are one of, if not the biggest external rotor motor manufacturers in the world, they have over 100 years of engineering experience behind them, which gives you the confidence. If a low cost painted finish fan is your choice this is among the best available.

 

Supplied fully assembled

Fully speed controllable

Can be used in any non hazardous environment

Suitable to run in temperatures from -40°C to up to 70°C in some instances

Low to medium air volumes

Low to medium static pressures

Available sizes 315mm – 630mm from stock

710mm – 1000mm check for availability

Tough epoxy paint finish

Die cast aluminium impellers (the bit that goes around)

Motor class F insulation with protection to IP54

All fans reversible for supply or extract

Extract fan ESP40014 ZAP400-41

Manufactured by Ziehl Abegg and distributed by Vent Axia and Systemair, this is probably one of the most popular plate mounted axials on the market today. Ziehl Abegg are one of, if not the biggest external rotor motor manufacturers in the world, they have over 100 years of engineering experience behind them, which gives you the confidence. If a low cost painted finish fan is your choice this is among the best available.

  • Supplied fully assembled
  • Fully speed controllable
  • Can be used in any non hazardous environment
  • Suitable to run in temperatures from -40°C to up to 70°C in some instances
  • Low to medium air volumes
  • Low to medium static pressures
  • Available sizes 315mm – 630mm from stock
  • 710mm – 1000mm check for availability
  • Tough epoxy paint finish
  • Die cast aluminium impellers (the bit that goes around)
  • Motor class F insulation with protection to IP54
  • All fans reversible for supply or extract

Extractor Fan ESP56014 /ZAP560-41

Manufactured by Ziehl Abegg and distributed by Vent Axia and Systemair, this is probably one of the most popular plate mounted axials on the market today. Ziehl Abegg are one of, if not the biggest external rotor motor manufacturers in the world, they have over 100 years of engineering experience behind them, which gives you the confidence. If a low cost painted finish fan is your choice this is among the best available.

 

Supplied fully assembled

Fully speed controllable

Can be used in any non hazardous environment

Suitable to run in temperatures from -40°C to up to 70°C in some instances

Low to medium air volumes

Low to medium static pressures

Available sizes 315mm – 630mm from stock

710mm – 1000mm check for availability

Tough epoxy paint finish

Die cast aluminium impellers (the bit that goes around)

Motor class F insulation with protection to IP54

All fans reversible for supply or extract

Extract Fan ESP63014 /ZAP630-41

Manufactured by Ziehl Abegg and distributed by Vent Axia and Systemair, this is probably one of the most popular plate mounted axials on the market today. Ziehl Abegg are one of, if not the biggest external rotor motor manufacturers in the world, they have over 100 years of engineering experience behind them, which gives you the confidence. If a low cost painted finish fan is your choice this is among the best available.

 

Supplied fully assembled

Fully speed controllable

Can be used in any non hazardous environment

Suitable to run in temperatures from -40°C to up to 70°C in some instances

Low to medium air volumes

Low to medium static pressures

Available sizes 315mm – 630mm from stock

710mm – 1000mm check for availability

Tough epoxy paint finish

Die cast aluminium impellers (the bit that goes around)

Motor class F insulation with protection to IP54

All fans reversible for supply or extract

Vent Axia 10303110A fan speed controller

The Vent-Axia Industrial range of electronic fan speed controllers manufactured by Vent-Axia. This range of fan speed controllers can be used with any Fan / Motor which is single phase – 240 volts and speed controllable using either 2 or 3 wire control (+earth).

 

W10303102M suitable for a maximum full load of 2.5 amps

10303103A suitable for a maximum full load of 3 amps

10303106A suitable for a maximum full load of 6 amps

10303110A suitable for a maximum full load of 10 amps

The Vent-Axia Industrial range of fan speed controllers can be used with any manufacturers fans / motors which are single phase and suitable for speed control via 2 or 3 wires (+earth) including

 

Flakt Woods

Ziehl Abegg

Elta

Helios

Solar and Palau

Nuaire

Systemair

Vent-Axia

Roof Units

Not sure if your fan is suitable? just ask and we can check for you

Vent Axia W10303102M fan speed controller

The Vent-Axia Industrial range of electronic fan speed controllers manufactured by Vent-Axia. This range of fan speed controllers can be used with any Fan / Motor which is single phase – 240 volts and speed controllable using either 2 or 3 wire control (+earth).

 

W10303102M suitable for a maximum full load of 2.5 amps

10303103A suitable for a maximum full load of 3 amps

10303106A suitable for a maximum full load of 6 amps

10303110A suitable for a maximum full load of 10 amps

The Vent-Axia Industrial range of fan speed controllers can be used with any manufacturers fans / motors which are single phase and suitable for speed control via 2 or 3 wires (+earth) including

 

Flakt Woods

Ziehl Abegg

Elta

Helios

Solar and Palau

Nuaire

Systemair

Vent-Axia

Roof Units

Not sure if your fan is suitable? just ask and we can check for you

.

Wall Ventilation External Gravity Shutter

terminates 100mm dia rigid or flexible ducting

 

terminates 100mm dia rigid or flexible ducting

This plastic gravity shutter is a cost effective solution when you need to terminate a hole in an external or internal wall.

 

This shutter an ideal fuss free solution, when only the shutter is required or when you need to customize your wall vent kit (usually when a standard wall sleeve isn’t long enough for the thickness of wall or cavity it’s going through)

 

Available sizes

 

To suit 100mm fan

To suit 150mm fan

Available colours

 

White

Brown

Pic shown is generic White, a Brown one will follow shortly

Please reload

bottom of page