GF805603 ESTOC TARGE POWERBOX 80-560-3

Another great square duct fan from FlaktWoods, constructed using a Pentapost frame which supports pre-galvanised steel sandwich panels, each filled with 20mm thick mineral wool for acoustic insulation. Each unit comes with 4 panels, all of which can be removed and relocated to give multiple outlet orientations at either 90 degrees to the inlet or 180 degrees for straight through air movement.

It operates at a higher temperature range than the Estoc Range as the motor is out of the airstream

Volumes Up to 5.5 m3/s (20,000 m3/h)

Pressures Up to 1400 pa (Static)

Impeller Backward Curved Impeller

Case Style Aluminium Penta-post Frame

Case Coating Pregalvanised Sheet Steel

Case Insulation Double Skinned 20mm Fiberglass

Installation Horizontal or Vertical

Location Internal or External with Cowl

IP rating IP54

Temperature Up to 75-110°C depending on size

30JM.33 1400 RPM SERIES 33 200 DEG C BIFURCATED FAN DB025607

Another great fan from FlaktWoods, Bifurcated Fans (sometimes shortened to Bifs or Bif Fans) are inline axial flow fans where the motor has been taken out of the airstream. This allows the fan to operate at higher temperatures.

Available sizes 152mm – 305mm from stock
The Casings are spun sheet steel, then hot dipped galvanised to give a finish highly resistant to corrosion and can be mounted external and internal
The impeller (the bit that goes around and moves the air) is aluminium silicon alloy
The motors are totally enclosed with class F insulation with protection to IP55.
The fans can be installed horizontal or vertical
They can be run upto 200Deg Continuos temperature
3ph fans only are suitable for speed control via inverter

31JM/16/4/5/40/1PH LONG CASED AXIAL FLOW EXTRACT FAN

The Flakt Woods JM axial flow extract fan range of cost effective highest quality long cased axials.

We think this product is the World’s best axial fan, and our recommended number one choice for every industrial and commercial application

The build quality and reliability are the highest we have ever experienced with fans still running since the range was introduced in the early 1990’s

Every time you fit this fan you know you’ve made the right choice, it will enhance your reputation for only using the best quality products

• Supplied fully assembled
• Fully speed controllable
• Can be used in any non hazardous environment (also available for hazardous application on request)
• Suitable in temperatures from -40°C to 50°C (70°C in some instances, please ask for details)
• Low to high air volumes
• Low to high static pressures
• Available sizes 315mm – 710mm from stock
• 800mm – 1000mm made to order, ring for availability
• 1000mm + check for availability
• The Casings are spun sheet steel, then hot dipped galvanised to give a finish highly resistant to corrosion and can be mounted external and internal
• The impeller (the bit that goes around and moves the air) is manufactured die cast aluminium
• The motors are totally enclosed with class F insulation with protection to IP55.

31JMP/16/4/5/32 FLAKTWOODS PLATE AXIAL

Features of another great plate axial from FlaktWoods

Diameters 315 mm to 630 mm

Volumes Up to 4.1 m3/s (14,750 m3/h)

Pressures Up to 175 Pa (Static)

Impeller Fixed Pitch, JM Aerofoil Case Style

Supplied fully assembled

The plate is made from steel and powder coated RAL 7001

Installation can be either horizontal or vertical

The fan can be mounted inside or outside

Operating temperature range is -40°C to + 70°C

All offered fans are suitable for speed control

35JM/16/4/5/22/1PH LONG CASED AXIAL FLOW FAN

The Flakt Woods JM axial flow extract fan range of cost effective highest quality long cased axials.

We think this product is the World’s best axial fan, and our recommended number one choice for every industrial and commercial application

The build quality and reliability are the highest we have ever experienced with fans still running since the range was introduced in the early 1990’s

Every time you fit this fan you know you’ve made the right choice, it will enhance your reputation for only using the best quality products

• Supplied fully assembled
• Fully speed controllable
• Can be used in any non hazardous environment (also available for hazardous application on request)
• Suitable in temperatures from -40°C to 50°C (70°C in some instances, please ask for details)
• Low to high air volumes
• Low to high static pressures
• Available sizes 315mm – 710mm from stock
• 800mm – 1000mm made to order, ring for availability
• 1000mm + check for availability
• The Casings are spun sheet steel, then hot dipped galvanised to give a finish highly resistant to corrosion and can be mounted external and internal
• The impeller (the bit that goes around and moves the air) is manufactured die cast aluminium
• The motors are totally enclosed with class F insulation with protection to IP55.

35JM/16/4/5/40/1PH LONG CASED AXIAL FLOW EXTRACT FAN

The Flakt Woods JM axial flow extract fan range of cost effective highest quality long cased axials.

We think this product is the World’s best axial fan, and our recommended number one choice for every industrial and commercial application

The build quality and reliability are the highest we have ever experienced with fans still running since the range was introduced in the early 1990’s

Every time you fit this fan you know you’ve made the right choice, it will enhance your reputation for only using the best quality products

Supplied fully assembled

Fully speed controllable

Can be used in any non hazardous environment (also available for hazardous application on request)

Suitable in temperatures from -40°C to 50°C (70°C in some instances, please ask for details)

Low to high air volumes

Low to high static pressures

Available sizes 315mm – 710mm from stock

800mm – 1000mm made to order, ring for availability

1000mm + check for availability

The Casings are spun sheet steel, then hot dipped galvanised to give a finish highly resistant to corrosion and can be mounted external and internal

The impeller (the bit that goes around and moves the air) is manufactured die cast aluminium

The motors are totally enclosed with class F insulation with protection to IP55.

35JMP/16/4/5/24 FLAKTWOODS PLATE AXIAL

Features of another great plate axial from FlaktWoods

Diameters 315 mm to 630 mm

Volumes Up to 4.1 m3/s (14,750 m3/h)

Pressures Up to 175 Pa (Static)

Impeller Fixed Pitch, JM Aerofoil Case Style

Supplied fully assembled

The plate is made from steel and powder coated RAL 7001

Installation can be either horizontal or vertical

The fan can be mounted inside or outside

Operating temperature range is -40°C to + 70°C

All offered fans are suitable for speed control

40JM MAXFAN HIGH PRESSURE LONG CASED AXIAL EXTRACT FAN

The Flakt Woods JmMax extract fan axial flow fan range of high performance and reliability 2 stage axial flow fans

This fan was introduced to satisfy ventilation systems where high pressure fans are required, where only single phase supply (240volts) is available and speed control is required

A typical application where this fan is commonly used is in the catering industry where a high level of filtration is required, usually the result of fitting odour control via Pre and Carbon Filters*

The build quality and reliability are the highest we have ever experienced, in a range of fans that are designed to work harder than most

Every time you fit this fan you know you’ve made the right choice, and it will enhance your reputation for only using the best quality products

Supplied fully assembled

Fully speed controllable

Can be used in any non hazardous environment

Suitable in temperatures from -40°C to 50°C

Low to high air volumes

Low to high static pressures

Available sizes 315mm – 630mm from stock

The Casings are spun sheet steel, then hot dipped galvanised to give a finish highly resistant to corrosion and can be mounted externally and internally

The impeller (the bit that goes around and moves the air) is manufactured die cast aluminium

The motors are totally enclosed with class F insulation with protection to IP55.

*High pressure systems can also consist of duct size restrictions, an unusual amount of ducting including a high number of bends, other forms of filtration such as Heppa Filters or Electrostatic filters. We can check the suitability of this fan for your application if required, please contact by any means you feel comfortable with and we’ll offer free advice

40JM.BIF (200)/20/2/6/32 3PH -

Another great fan from FlaktWoods, Bifurcated (sometimes shortened to Bifs or Bif Fans) are inline axial flow fans where the motor has been taken out of the airstream. This allows the fan to operate at higher temperatures.

Available sizes 400mm – 630mm from stock

800mm and 1000mm ring for availability

The Casings are spun sheet steel, then hot dipped galvanised to give a finish highly resistant to corrosion and can be mounted external and internal

The impeller (the bit that goes around and moves the air) is manufactured die cast aluminium

The motors are totally enclosed with class F insulation with protection to IP55.

The fans can be installed horizontal or vertical

They can be run upto 200Deg Continuos temperature

All suitable for speed control via inverter

40JM/16/4/5/40/1PH LONG CASED AXIAL FLOW EXTRACT FAN

The Flakt Woods JM axial flow extract fan range of cost effective highest quality long cased axials.

We think this product is the World’s best axial fan, and our recommended number one choice for every industrial and commercial application

The build quality and reliability are the highest we have ever experienced with fans still running since the range was introduced in the early 1990’s

Every time you fit this fan you know you’ve made the right choice, it will enhance your reputation for only using the best quality products

• Supplied fully assembled
• Fully speed controllable
• Can be used in any non hazardous environment (also available for hazardous application on request)
• Suitable in temperatures from -40°C to 50°C (70°C in some instances, please ask for details)
• Low to high air volumes
• Low to high static pressures
• Available sizes 315mm – 710mm from stock
• 800mm – 1000mm made to order, ring for availability
• 1000mm + check for availability
• The Casings are spun sheet steel, then hot dipped galvanised to give a finish highly resistant to corrosion and can be mounted external and internal
• The impeller (the bit that goes around and moves the air) is manufactured die cast aluminium
• The motors are totally enclosed with class F insulation with protection to IP55.

30JM.33 2900 RPM SERIES 33 200 DEG C BIFURCATED FAN

Another great fan from FlaktWoods, Bifurcated Fans (sometimes shortened to Bifs or Bif Fans) are inline axial flow fans where the motor has been taken out of the airstream. This allows the fan to operate at higher temperatures.

Available sizes 152mm – 305mm from stock
The Casings are spun sheet steel, then hot dipped galvanised to give a finish highly resistant to corrosion and can be mounted external and internal
The impeller (the bit that goes around and moves the air) is aluminium silicon alloy
The motors are totally enclosed with class F insulation with protection to IP55.
The fans can be installed horizontal or vertical
They can be run upto 200Deg Continuos temperature
3ph fans only are suitable for speed control via inverter

.

315 MOUNTING FEET

Supplied in pairs

315mm Mounting Foot, used to fit directly to the fan as part of a full ancillary package

The Mounting Foot can be used to mount the fan in the horizontal or vertical position

Usually used in conjunction with Anti Vibration Mounts

Can also be used to fit directly to Silencers with or without Anti Vibration Mo

CDA 400 X 1D STRAIGHT THROUGH SILENCER

400mm dia x 400mm long straight through silencer (generally reduces a fan noise level by 7-10dB (A)* Can be supplied to either bolt directly to any manufacturer of cased axial or with spigots to mount inline with ducting.

The addition of this silencer to a system will act in the same way a silencer does on a car, so if you've ever heard a car with no silencer fitted, this gives you an idea of the impact a silencer can have on a system.

Please Note - for a straight through silencer to work to have the maximum impact on a system, a silencer should be fixed either side of the fan, this will give 3 benefits to the overall noise level of the system.

1. System side (usually the noise level inside a building) noise level is reduced

2. Atmospheric side (usually the noise level outside a building) noise level is reduced

3. The breakout from the fan is reduced, this could be a big factor depending where the fan is fitted, such as a false ceiling in a class room or office area

*Noise is a complicated medium to get right, if in doubt or you have specific target levels to achieve, please contact us via any means you feel comfortable with and we'll find a solution to your problem

CDA 500 X 1D STRAIGHT THROUGH SILENCER

500mm dia x 500mm long straight through silencer (generally reduces a fan noise level by 7-10dB (A)* Can be supplied to either bolt directly to any manufacturer of cased axial or with spigots to mount inline with ducting.

The addition of this silencer to a system will act in the same way a silencer does on a car, so if you've ever heard a car with no silencer fitted, this gives you an idea of the impact a silencer can have on a system.

Please Note - for a straight through silencer to work to have the maximum impact on a system, a silencer should be fixed either side of the fan, this will give 3 benefits to the overall noise level of the system.

1. System side (usually the noise level inside a building) noise level is reduced

2. Atmospheric side (usually the noise level outside a building) noise level is reduced

3. The breakout from the fan is reduced, this could be a big factor depending where the fan is fitted, such as a false ceiling in a class room or office area

*Noise is a complicated medium to get right, if in doubt or you have specific target levels to achieve, please contact us via any means you feel comfortable with and we'll find a solution to your problem

ESPADA ILC100 REPLACES ILC

An easy to install 1ph in-line fan from FlaktWoods. These fans have all the advantages of axial flow fans combined with the benefits of radial fan pressure

Diameters 100 mm to 315 mm in stock
Volumes Up to 0.48 m3/s (1,730 m3/h)
Pressures Up to 700 Pa (Static)
Impeller LB Backward Blade
Case Style Impact Resistant Plastic
Case Coating Inflammable Plastic

Can be installed horizontally or vertical
Suitable for mounting inside or outside
Temperature rating up to 70°C
All fans suitable for speed control

Please note the mounting foot needs to be ordered separately.

ESPADA ILC125 REPLACES ILC

An easy to install 1ph in-line fan from FlaktWoods. These fans have all the advantages of axial flow fans combined with the benefits of radial fan pressure

Diameters 100 mm to 315 mm in stock
Volumes Up to 0.48 m3/s (1,730 m3/h)
Pressures Up to 700 Pa (Static)
Impeller LB Backward Blade
Case Style Impact Resistant Plastic
Case Coating Inflammable Plastic

Can be installed horizontally or vertical
Suitable for mounting inside or outside
Temperature rating up to 70°C
All fans suitable for speed control

Please note the mounting foot needs to be ordered separately.

ESPADA ILC150 REPLACES ILC

An easy to install 1ph in-line fan from FlaktWoods. These fans have all the advantages of axial flow fans combined with the benefits of radial fan pressure

Diameters 100 mm to 315 mm in stock

Volumes Up to 0.48 m3/s (1,730 m3/h)

Pressures Up to 700 Pa (Static)

Impeller LB Backward Blade

Case Style Impact Resistant Plastic

Case Coating Inflammable Plastic

Can be installed horizontally or vertical

Suitable for mounting inside or outside

Temperature rating up to 70°C

All fans suitable for speed control

Please note the mounting foot needs to be ordered separately.

2102/400/4/1PH PLATE MOUNTED EXTRACT FAN

The Flakt Woods 2102 range of low cost high quality plate mounted extract fans.

Our recommended number one plate mounted fan choice

Flakt Woods reputation for only manufacturing the highest quality products is evident with this low cost range of Plate mounted Fans. Buying this fan gives you the confidence and satisfaction that comes with over 100 years of fan engineering experience.

Supplied fully assembled

Fully speed controllable

Can be used in any non hazardous environment

Suitable in temperatures from -40°C to 50°C

Low to medium air volumes

Low to medium static pressures

Available sizes 315mm – 500mm from stock

560mm – 710mm made to order in 3 weeks

The grey coloured plate is manufactured from mild steel with a powder coat painted finish.

The impeller (the bit that goes around and moves the air) is manufactured from glass filled polypropylene and will stay intact up to temperatures of over 100°C

The motors are totally enclosed with class F insulation with protection to IP55. Single phase motors have overheat protection

2102/450/4/1PH PLATE MOUNTED EXTRACT FAN

The Flakt Woods 2102 range of low cost high quality plate mounted extract fans.

Our recommended number one plate mounted fan choice

Flakt Woods reputation for only manufacturing the highest quality products is evident with this low cost range of Plate mounted Fans. Buying this fan gives you the confidence and satisfaction that comes with over 100 years of fan engineering experience.

Supplied fully assembled

Fully speed controllable

Can be used in any non hazardous environment

Suitable in temperatures from -40°C to 50°C

Low to medium air volumes

Low to medium static pressures

Available sizes 315mm – 500mm from stock

560mm – 710mm made to order in 3 weeks

The grey coloured plate is manufactured from mild steel with a powder coat painted finish.

The impeller (the bit that goes around and moves the air) is manufactured from glass filled polypropylene and will stay intact up to temperatures of over 100°C

The motors are totally enclosed with class F insulation with protection to IP55. Single phase motors have overheat protection

25JM.33 1400 RPM SERIES 33 200 DEG C BIFURCATED FAN DB215607

Another great fan from FlaktWoods, Bifurcated (sometimes shortened to Bifs or Bif Fans) are inline axial flow fans where the motor has been taken out of the airstream. This allows the fan to operate at higher temperatures.

Available sizes 152mm – 305mm from stock
The Casings are spun sheet steel, then hot dipped galvanised to give a finish highly resistant to corrosion and can be mounted external and internal
The impeller (the bit that goes around and moves the air) is manufactured die cast aluminium
The motors are totally enclosed with class F insulation with protection to IP55.
The fans can be installed horizontal or vertical
They can be run upto 200Deg Continuos temperature
3ph fans only are suitable for speed control via inverter

25JM.33 2900 RPM SERIES 33 200 DEG C BIFURCATED FAN DB215609

Another great fan from FlaktWoods, Bifurcated Fans (sometimes shortened to Bifs or Bif Fans) are inline axial flow fans where the motor has been taken out of the airstream. This allows the fan to operate at higher temperatures.

Available sizes 152mm – 305mm from stock

The Casings are spun sheet steel, then hot dipped galvanised to give a finish highly resistant to corrosion and can be mounted external and internal

The impeller (the bit that goes around and moves the air) is aluminium silicon alloy

The motors are totally enclosed with class F insulation with protection to IP55.

The fans can be installed horizontal or vertical

They can be run upto 200Deg Continuos temperature

3ph fans only are suitable for speed control via inverter

15JM.33 2900 RPM SERIES 33 200 DEG C BIFURCATED FAN DB125603

Another great fan from FlaktWoods, Bifurcated Fans (sometimes shortened to Bifs or Bif Fans) are inline axial flow fans where the motor has been taken out of the airstream. This allows the fan to operate at higher temperatures.

Available sizes 152mm – 305mm from stock
The Casings are spun sheet steel, then hot dipped galvanised to give a finish highly resistant to corrosion and can be mounted external and internal
The impeller (the bit that goes around and moves the air) is aluminium silicon alloy
The motors are totally enclosed with class F insulation with protection to IP55.
The fans can be installed horizontal or vertical
They can be run upto 200Deg Continuos temperature
3ph fans only are suitable for speed control via inverter

2102/315/4/1PH PLATE MOUNTED EXTRACT FAN

The Flakt Woods 2102 range of low cost high quality plate mounted fans.

Our recommended number one plate mounted fan choice.

Flakt Woods reputation for only manufacturing the highest quality products is evident with this low cost range of Plate mounted Fans. Buying this fan gives you the confidence and satisfaction that comes with over 100 years of fan engineering experience.

Supplied fully assembled

Fully speed controllable

Can be used in any non hazardous environment

Suitable in temperatures from -40°C to 50°C

Low to medium air volumes

Low to medium static pressures

Available sizes 315mm – 500mm from stock

560mm – 710mm made to order in 3 weeks

The grey coloured plate is manufactured from mild steel with a powder coat painted finish.

The impeller (the bit that goes around and moves the air) is manufactured from glass filled polypropylene and will stay intact up to temperatures of over 100°C

The motors are totally enclosed with class F insulation with protection to IP55. Single phase motors have overheat protection

2102/355/4/1PH PLATE MOUNTED EXTRACT FAN

The Flakt Woods 2102 range of low cost high quality plate mounted extract fans.

Our recommended number one plate mounted fan choice

Flakt Woods reputation for only manufacturing the highest quality products is evident with this low cost range of Plate mounted Fans. Buying this fan gives you the confidence and satisfaction that comes with over 100 years of fan engineering experience.

• Supplied fully assembled
• Fully speed controllable
• Can be used in any non hazardous environment
• Suitable in temperatures from -40°C to 50°C
• Low to medium air volumes
• Low to medium static pressures
• Available sizes 315mm – 500mm from stock
• 560mm – 710mm made to order in 3 weeks
• The grey coloured plate is manufactured from mild steel with a powder coat painted finish.
• The impeller (the bit that goes around and moves the air) is manufactured from glass filled polypropylene and will stay intact up to temperatures of over 100°C
• The motors are totally enclosed with class F insulation with protection to IP55. Single phase motors have overheat protection

ME SERIES ELECTRONIC FAN SPEED CONTROLLERS

Your own brand. Your own contact details. Your own design - On any ME Series Electronic Fan Speed Controller *

* Minimum order quantity of 25

Your chance to have your own branded market leading Flakt Woods ME series electronic fan speed controllers. Just imagine your customer has a problem, and whats there right in front of them, your brand, with your contact details, you can't put a price on this incredible after sales oppurtunity.

The whole range is available for you to buy, for less than you think, and remember these controllers can be used with any manufacturer of fans

You have the freedom to decide on the whole design including colour and fonts, add as much or as little as you feel appropriate

This is a unque oppurtuntity and for a limited time is on special offer, but hurry it won't last for ever

Models available are:

• ME1.1
• ME1.3
• ME1.6
• ME1.12

Note: A minimum of 25 off any of sizes can be ordered, so if all you want is 25 off ME1.6's your in luck. Unfortunately we can't accept an order of mixed sized controllers.

BT414010 MOTOR

Replacement motor

What does the code mean

• BT = motor dia
• 4 = motor length
• 1 = single phase
• 010 = Kw rating

CDA 315 X 1D STRAIGHT THROUGH SILENCER

315mm dia x 315mm long straight through silencer (generally reduces a fan noise level by 7-10dB (A)* Can be supplied to either bolt directly to any manufacturer of cased axial or with spigots to mount inline with ducting.

The addition of this silencer to a system will act in the same way a silencer does on a car, so if you've ever heard a car with no silencer fitted, this gives you an idea of the impact a silencer can have on a system.

Please Note - for a straight through silencer to work to have the maximum impact on a system, a silencer should be fixed either side of the fan, this will give 3 benefits to the overall noise level of the system.

1. System side (usually the noise level inside a building) noise level is reduced

2. Atmospheric side (usually the noise level outside a building) noise level is reduced

3. The breakout from the fan is reduced, this could be a big factor depending where the fan is fitted, such as a false ceiling in a class room or office area

*Noise is a complicated medium to get right, if in doubt or you have specific target levels to achieve, please contact us via any means you feel comfortable with and we'll find a solution to your problem

CDA 355 X 1D STRAIGHT THROUGH SILENCER

355mm dia x 355mm long straight through silencer (generally reduces a fan noise level by 7-10dB (A)* Can be supplied to either bolt directly to any manufacturer of cased axial or with spigots to mount inline with ducting.

The addition of this silencer to a system will act in the same way a silencer does on a car, so if you've ever heard a car with no silencer fitted, this gives you an idea of the impact a silencer can have on a system.

Please Note - for a straight through silencer to work to have the maximum impact on a system, a silencer should be fixed either side of the fan, this will give 3 benefits to the overall noise level of the system.

1. System side (usually the noise level inside a building) noise level is reduced

2. Atmospheric side (usually the noise level outside a building) noise level is reduced

3. The breakout from the fan is reduced, this could be a big factor depending where the fan is fitted, such as a false ceiling in a class room or office area

*Noise is a complicated medium to get right, if in doubt or you have specific target levels to achieve, please contact us via any means you feel comfortable with and we'll find a solution to your problem

50JM/20/4/6/32/1PH LONG CASED AXIAL FLOW FAN

The Flakt Woods JM axial flow extract fan range of cost effective highest quality long cased axials.

We think this product is the World’s best axial fan, and our recommended number one choice for every industrial and commercial application

The build quality and reliability are the highest we have ever experienced with fans still running since the range was introduced in the early 1990’s

Every time you fit this fan you know you’ve made the right choice, it will enhance your reputation for only using the best quality products

Supplied fully assembled

Fully speed controllable

Can be used in any non hazardous environment (also available for hazardous application on request)

Suitable in temperatures from -40°C to 50°C (70°C in some instances, please ask for details)

Low to high air volumes

Low to high static pressures

Available sizes 315mm – 710mm from stock

800mm – 1000mm made to order, ring for availability

1000mm + check for availability

The Casings are spun sheet steel, then hot dipped galvanised to give a finish highly resistant to corrosion and can be mounted external and internal

The impeller (the bit that goes around and moves the air) is manufactured die cast aluminium

The motors are totally enclosed with class F insulation with protection to IP55.

50JMP/20/4/6/32 FLAKTWOODS PLATE AXIAL

Diameters 315 mm to 630 mm
Volumes Up to 4.1 m3/s (14,750 m3/h)
Pressures Up to 175 Pa (Static)
Impeller Fixed Pitch, JM Aerofoil Case Style

Supplied fully assembled
The plate is made from steel and powder coated RAL 7001
Installation can be either horizontal or vertical
The fan can be mounted inside or outside
Operating temperature range is -40°C to + 70°C
All offered fans are suitable for speed control

56JMP/20/4/6/24 FLAKTWOODS PLATE AXIAL

Features of another great plate axial from FlaktWoods

Diameters 315 mm to 630 mm

Volumes Up to 4.1 m3/s (14,750 m3/h)

Pressures Up to 175 Pa (Static)

Impeller Fixed Pitch, JM Aerofoil Case Style

Supplied fully assembled

The plate is made from steel and powder coated RAL 7001

Installation can be either horizontal or vertical

The fan can be mounted inside or outside

Operating temperature range is -40°C to + 70°C

All offered fans are suitable for speed control

630MM LOUVRE SHUTTER

A Louvre Shutter is a gravity type shutter which can be used to terminate and weather extract systems. When the fan is running the plastic blades will open allowing the air to be extracted from the system, and when the fan is not running will be closed, this helps to prevent back draughts and water ingress

The shutter is commonly used to terminate systems where a plate mounted fan has been fitted internally, and used for extraction

Louvre shutters are usually either mounted to an external wall or at the end of a galvanised box to terminate an extract system

This Louvre shutter can only be used on EXTRACT systems, for SUPPLY systems please contact us direct, by any means you feel comfortable with and we will advise what should be used to suit your application

63JM MAXFAN HIGH PRESSURE LONG CASED AXIAL EXTRACT FAN