45JM/16/4/5/40/1PH LONG CASED AXIAL FLOW EXTRACT FAN
The Flakt Woods JM axial flow extract fan range of cost effective highest quality long cased axials.
We think this product is the World’s best axial fan, and our recommended number one choice for every industrial and commercial application
The build quality and reliability are the highest we have ever experienced with fans still running since the range was introduced in the early 1990’s
Every time you fit this fan you know you’ve made the right choice, it will enhance your reputation for only using the best quality products
- Supplied fully assembled
- Fully speed controllable
- Can be used in any non hazardous environment (also available for hazardous application on request)
- Suitable in temperatures from -40°C to 50°C (70°C in some instances, please ask for details)
- Low to high air volumes
- Low to high static pressures
- Available sizes 315mm – 710mm from stock
- 800mm – 1000mm made to order, ring for availability
- 1000mm + check for availability
- The Casings are spun sheet steel, then hot dipped galvanised to give a finish highly resistant to corrosion and can be mounted external and internal
- The impeller (the bit that goes around and moves the air) is manufactured die cast aluminium
- The motors are totally enclosed with class F insulation with protection to IP55.
50JM MAXFAN HIGH PRESSURE LONG CASED AXIAL EXTRACT FAN
The Flakt Woods JmMax fan axial flow extract fan range of high performance and reliability 2 stage axial flow fans
This fan was introduced to satisfy ventilation systems where high pressure fans are required, where only single phase supply (240volts) is available and speed control is required
A typical application where this fan is commonly used is in the catering industry where a high level of filtration is required, usually the result of fitting odour control via Pre and Carbon Filters*
The build quality and reliability are the highest we have ever experienced, in a range of fans that are designed to work harder than most
Every time you fit this fan you know you’ve made the right choice, and it will enhance your reputation for only using the best quality products
Supplied fully assembled
Fully speed controllable
Can be used in any non hazardous environment
Suitable in temperatures from -40°C to 50°C
Low to high air volumes
Low to high static pressures
Available sizes 315mm – 630mm from stock
The Casings are spun sheet steel, then hot dipped galvanised to give a finish highly resistant to corrosion and can be mounted externally and internally
The impeller (the bit that goes around and moves the air) is manufactured die cast aluminium
The motors are totally enclosed with class F insulation with protection to IP55.
*High pressure systems can also consist of duct size restrictions, an unusual amount of ducting including a high number of bends, other forms of filtration such as Heppa Filters or Electrostatic filters. We can check the suitability of this fan for your application if required, please contact by any means you feel comfortable with and we’ll offer free advice
50JM.BIF (200)/20/4/6//32 3PH
Another great fan from FlaktWoods, Bifurcated (sometines shortened to Bifs or Bif Fans) are inline axial flow fans where the motor has been taken out of the airstream. This allows the fan to operate at higher temperatures.
Available sizes 400mm – 630mm from stock
800mm and 1000mm ring for availability
The Casings are spun sheet steel, then hot dipped galvanised to give a finish highly resistant to corrosion and can be mounted external and internal
The impeller (the bit that goes around and moves the air) is manufactured die cast aluminium
The motors are totally enclosed with class F insulation with protection to IP55.
The fans can be installed horizontal or vertical
They can be run upto 200Deg Continuos temperature
All suitable for speed control via inverter
50JM/20/4/6/32/1PH LONG CASED AXIAL FLOW EXTRACT FAN
The Flakt Woods JM axial flow extract fan range of cost effective highest quality long cased axials.
We think this product is the World’s best axial fan, and our recommended number one choice for every industrial and commercial application
The build quality and reliability are the highest we have ever experienced with fans still running since the range was introduced in the early 1990’s
Every time you fit this fan you know you’ve made the right choice, it will enhance your reputation for only using the best quality products
Supplied fully assembled
Fully speed controllable
Can be used in any non hazardous environment (also available for hazardous application on request)
Suitable in temperatures from -40°C to 50°C (70°C in some instances, please ask for details)
Low to high air volumes
Low to high static pressures
Available sizes 315mm – 710mm from stock
800mm – 1000mm made to order, ring for availability
1000mm + check for availability
The Casings are spun sheet steel, then hot dipped galvanised to give a finish highly resistant to corrosion and can be mounted external and internal
The impeller (the bit that goes around and moves the air) is manufactured die cast aluminium
The motors are totally enclosed with class F insulation with protection to IP55.
56JM/16/4/5/32/1PH LONG CASED AXIAL FLOW
The Flakt Woods JM axial flow extract fan range of cost effective highest quality long cased axials.
We think this product is the World’s best axial fan, and our recommended number one choice for every industrial and commercial application
The build quality and reliability are the highest we have ever experienced with fans still running since the range was introduced in the early 1990’s
Every time you fit this fan you know you’ve made the right choice, it will enhance your reputation for only using the best quality products
Supplied fully assembled
Fully speed controllable
Can be used in any non hazardous environment (also available for hazardous application on request)
Suitable in temperatures from -40°C to 50°C (70°C in some instances, please ask for details)
Low to high air volumes
Low to high static pressures
Available sizes 315mm – 710mm from stock
800mm – 1000mm made to order, ring for availability
1000mm + check for availability
The Casings are spun sheet steel, then hot dipped galvanised to give a finish highly resistant to corrosion and can be mounted external and internal
The impeller (the bit that goes around and moves the air) is manufactured die cast aluminium
The motors are totally enclosed with class F insulation with protection to IP55
56JM/20/4/6/28/1PH LONG CASED AXIAL FLOW EXTRACT FAN
The Flakt Woods JM axial flow extract fan range of cost effective highest quality long cased axials.
We think this product is the World’s best axial fan, and our recommended number one choice for every industrial and commercial application
The build quality and reliability are the highest we have ever experienced with fans still running since the range was introduced in the early 1990’s
Every time you fit this fan you know you’ve made the right choice, it will enhance your reputation for only using the best quality products
- Supplied fully assembled
- Fully speed controllable
- Can be used in any non hazardous environment (also available for hazardous application on request)
- Suitable in temperatures from -40°C to 50°C (70°C in some instances, please ask for details)
- Low to high air volumes
- Low to high static pressures
- Available sizes 315mm – 710mm from stock
- 800mm – 1000mm made to order, ring for availability
- 1000mm + check for availability
- The Casings are spun sheet steel, then hot dipped galvanised to give a finish highly resistant to corrosion and can be mounted external and internal
- The impeller (the bit that goes around and moves the air) is manufactured die cast aluminium
- The motors are totally enclosed with class F insulation with protection to IP55.
63JM MAXFAN HIGH PRESSURE LONG CASED AXIAL EXTRACT FAN
The Flakt Woods JmMax fan axial flow extract fan range of high performance and reliability 2 stage axial flow fans
This fan was introduced to satisfy ventilation systems where high pressure fans are required, where only single phase supply (240volts) is available and speed control is required
A typical application where this fan is commonly used is in the catering industry where a high level of filtration is required, usually the result of fitting odour control via Pre and Carbon Filters*
The build quality and reliability are the highest we have ever experienced, in a range of fans that are designed to work harder than most
Every time you fit this fan you know you’ve made the right choice, and it will enhance your reputation for only using the best quality products
Supplied fully assembled
Fully speed controllable
Can be used in any non hazardous environment
Suitable in temperatures from -40°C to 50°C
Low to high air volumes
Low to high static pressures
Available sizes 315mm – 630mm from stock
The Casings are spun sheet steel, then hot dipped galvanised to give a finish highly resistant to corrosion and can be mounted externally and internally
The impeller (the bit that goes around and moves the air) is manufactured die cast aluminium
The motors are totally enclosed with class F insulation with protection to IP55.
*High pressure systems can also consist of duct size restrictions, an unusual amount of ducting including a high number of bends, other forms of filtration such as Heppa Filters or Electrostatic filters. We can check the suitability of this fan for your application if required, please contact by any means you feel comfortable with and we’ll offer free advice
63JM.BIF (200)/20/4/6//30 3PH
Another great fan from FlaktWoods, Bifurcated (sometines shortened to Bifs or Bif Fans) are inline axial flow fans where the motor has been taken out of the airstream. This allows the fan to operate at higher temperatures.
Available sizes 400mm – 630mm from stock
800mm and 1000mm ring for availability
The Casings are spun sheet steel, then hot dipped galvanised to give a finish highly resistant to corrosion and can be mounted external and internal
The impeller (the bit that goes around and moves the air) is manufactured die cast aluminium
The motors are totally enclosed with class F insulation with protection to IP55.
The fans can be installed horizontal or vertical
They can be run upto 200Deg Continuos temperature
All suitable for speed control via inverter
63JM/20/4/6/16/1PH LONG CASED AXIAL FLOW EXTRACT FAN
The Flakt Woods JM axial flow extract fan range of cost effective highest quality long cased axials.
We think this product is the World’s best axial fan, and our recommended number one choice for every industrial and commercial application. The build quality and reliability are the highest we have ever experienced with fans still running since the range was introduced in the early 1990’s. Every time you fit this fan you know you’ve made the right choice, it will enhance your reputation for only using the best quality products.
Supplied fully assembled
Fully speed controllable
Can be used in any non hazardous environment
(also available for hazardous application on request)
Suitable in temperatures from -40°C to 50°C (70°C in some instances, please ask for details)
Low to high air volumes
Low to high static pressures
Available sizes 315mm – 710mm from stock
800mm – 1000mm made to order, ring for availability
1000mm + check for availability
The Casings are spun sheet steel, then hot dipped galvanised to give a finish highly resistant to corrosion and can be mounted external and internal. The impeller (the bit that goes around and moves the air) is manufactured die cast aluminium. The motors are totally enclosed with class F insulation with protection to IP55
15JM.33 2900 RPM SERIES 33 200 DEG C BIFURCATED FAN DB125603
Overview
Another great fan from FlaktWoods, Bifurcated Fans (sometimes shortened to Bifs or Bif Fans) are inline axial flow fans where the motor has been taken out of the airstream. This allows the fan to operate at higher temperatures.
Available sizes 152mm – 305mm from stock
The Casings are spun sheet steel, then hot dipped galvanised to give a finish highly resistant to corrosion and can be mounted external and internal
The impeller (the bit that goes around and moves the air) is aluminium silicon alloy
The motors are totally enclosed with class F insulation with protection to IP55.
The fans can be installed horizontal or vertical
They can be run upto 200Deg Continuos temperature
3ph fans only are suitable for speed control via inverter
2102/315/4/1PH PLATE MOUNTED EXTRACT FAN BY FLAKT WOODS
The Flakt Woods 2102 range of low cost high quality plate mounted fans.
Our recommended number one plate mounted fan choice.
Flakt Woods reputation for only manufacturing the highest quality products is evident with this low cost range of Plate mounted Fans. Buying this fan gives you the confidence and satisfaction that comes with over 100 years of fan engineering experience.
Supplied fully assembled
Fully speed controllable
Can be used in any non hazardous environment
Suitable in temperatures from -40°C to 50°C
Low to medium air volumes
Low to medium static pressures
Available sizes 315mm – 500mm from stock
560mm – 710mm made to order in 3 weeks
The grey coloured plate is manufactured from mild steel with a powder coat painted finish.
The impeller (the bit that goes around and moves the air) is manufactured from glass filled polypropylene and will stay intact up to temperatures of over 100°C
The motors are totally enclosed with class F insulation with protection to IP55. Single phase motors have overheat protection
2102/355/4/1PH PLATE MOUNTED EXTRACT FAN BY FLAKT WOODS
The Flakt Woods 2102 range of low cost high quality plate mounted extract fans.
Our recommended number one plate mounted fan choice
Flakt Woods reputation for only manufacturing the highest quality products is evident with this low cost range of Plate mounted Fans. Buying this fan gives you the confidence and satisfaction that comes with over 100 years of fan engineering experience.
-
Supplied fully assembled
-
Fully speed controllable
-
Can be used in any non hazardous environment
-
Suitable in temperatures from -40°C to 50°C
-
Low to medium air volumes
-
Low to medium static pressures
-
Available sizes 315mm – 500mm from stock
-
560mm – 710mm made to order in 3 weeks
-
The grey coloured plate is manufactured from mild steel with a powder coat painted finish.
-
The impeller (the bit that goes around and moves the air) is manufactured from glass filled polypropylene and will stay intact up to temperatures of over 100°C
- The motors are totally enclosed with class F insulation with protection to IP55. Single phase motors have overheat protection
Long Cased Axial Flow Fan 31JM
EJ321460 replaces the obsolete DX321460
EJ321460 replaces the obsolete DX321460
The Flakt Woods JM axial flow extract fan range of cost effective highest quality long cased axials.
We think this product is the World’s best axial fan, and our recommended number one choice for every industrial and commercial application
56Jm MaxFan high pressure long cased axial extract fan
The Flakt Woods JmMax fan axial flow extract fan range of high performance and reliability 2 stage axial flow fans
This fan was introduced to satisfy ventilation systems where high pressure fans are required, where only single phase supply (240volts) is available and speed control is required
A typical application where this fan is commonly used is in the catering industry where a high level of filtration is required, usually the result of fitting odour control via Pre and Carbon Filters*
The build quality and reliability are the highest we have ever experienced, in a range of fans that are designed to work harder than most
Every time you fit this fan you know you’ve made the right choice, and it will enhance your reputation for only using the best quality products
- Supplied fully assembled
- Fully speed controllable
- Can be used in any non hazardous environment
- Suitable in temperatures from -40°C to 50°C
- Low to high air volumes
- Low to high static pressures
- Available sizes 315mm – 630mm from stock
The Casings are spun sheet steel, then hot dipped galvanised to give a finish highly resistant to corrosion and can be mounted externally and internally
The impeller (the bit that goes around and moves the air) is manufactured die cast aluminium
The motors are totally enclosed with class F insulation with protection to IP55.
*High pressure systems can also consist of duct size restrictions, an unusual amount of ducting including a high number of bends, other forms of filtration such as Heppa Filters or Electrostatic filters. We can check the suitability of this fan for your application if required, please contact by any means you feel comfortable with and we’ll offer free advice
The Flakt Woods JM axial flow extract fan range of cost effective highest quality long cased axials.
We think this product is the World’s best axial fan, and our recommended number one choice for every industrial and commercial application
The build quality and reliability are the highest we have ever experienced with fans still running since the range was introduced in the early 1990’s
Every time you fit this fan you know you’ve made the right choice, it will enhance your reputation for only using the best quality products
Supplied fully assembled
Fully speed controllable
Can be used in any non hazardous environment (also available for hazardous application on request)
Suitable in temperatures from -40°C to 50°C (70°C in some instances, please ask for details)
Low to high air volumes
Low to high static pressures
Available sizes 315mm – 710mm from stock
800mm – 1000mm made to order, ring for availability
1000mm + check for availability
The Casings are spun sheet steel, then hot dipped galvanised to give a finish highly resistant to corrosion and can be mounted external and internal
The impeller (the bit that goes around and moves the air) is manufactured die cast aluminium
The motors are totally enclosed with class F insulation with protection to IP55.
The Flakt Woods JM axial flow extract fan range of cost effective highest quality long cased axials.
We think this product is the World’s best axial fan, and our recommended number one choice for every industrial and commercial application
The build quality and reliability are the highest we have ever experienced with fans still running since the range was introduced in the early 1990’s
Every time you fit this fan you know you’ve made the right choice, it will enhance your reputation for only using the best quality products
Supplied fully assembled
Fully speed controllable
Can be used in any non hazardous environment (also available for hazardous application on request)
Suitable in temperatures from -40°C to 50°C (70°C in some instances, please ask for details)
Low to high air volumes
Low to high static pressures
Available sizes 315mm – 710mm from stock
800mm – 1000mm made to order, ring for availability
1000mm + check for availability
The Casings are spun sheet steel, then hot dipped galvanised to give a finish highly resistant to corrosion and can be mounted external and internal
The impeller (the bit that goes around and moves the air) is manufactured die cast aluminium
The motors are totally enclosed with class F insulation with protection to IP55.
The Flakt Woods JM axial flow extract fan range of cost effective highest quality long cased axials.
We think this product is the World’s best axial fan, and our recommended number one choice for every, industrial and commercial application
The build quality and reliability are the highest we have ever experienced with fans still running since the range was introduced in the early 1990’s
Every time you fit this fan you know you’ve made the right choice, and it will enhance your reputation for only using the best quality products
Supplied fully assembled
Fully speed controllable
Can be used in any none hazardous environment (also available for hazardous application on request)
Suitable in temperatures from -40°C to 50°C (70°C in some instances, please ask for details)
Low to high air volumes
Low to high static pressures
Available sizes 315mm – 710mm from stock
800mm – 1000mm made to order, ring for availability
1000mm + ring for availability
The Casings are spun sheet steel, then hot dipped galvanised to give a finish highly resistant to corrosion and can be mounted external and internal
The impeller (the bit that goes around and moves the air) is manufactured die cast aluminium
The motors are totally enclosed with class F insulation with protection to IP55.
The Flakt Woods JM axial flow extract fan range of cost effective highest quality long cased axials.
We think this product is the World’s best axial fan, and our recommended number one choice for every, industrial and commercial application
The build quality and reliability are the highest we have ever experienced with fans still running since the range was introduced in the early 1990’s
Every time you fit this fan you know you’ve made the right choice, and it will enhance your reputation for only using the best quality products
Supplied fully assembled
Fully speed controllable
Can be used in any none hazardous environment (also available for hazardous application on request)
Suitable in temperatures from -40°C to 50°C (70°C in some instances, please ask for details)
Low to high air volumes
Low to high static pressures
Available sizes 315mm – 710mm from stock
800mm – 1000mm made to order, ring for availability
1000mm + ring for availability
The Casings are spun sheet steel, then hot dipped galvanised to give a finish highly resistant to corrosion and can be mounted external and internal
The impeller (the bit that goes around and moves the air) is manufactured die cast aluminium
The motors are totally enclosed with class F insulation with protection to IP55
The Flakt Woods JM axial flow extract fan range of cost effective highest quality long cased axials.
We think this product is the World’s best axial fan, and our recommended number one choice for every, industrial and commercial application
The build quality and reliability are the highest we have ever experienced with fans still running since the range was introduced in the early 1990’s
Every time you fit this fan you know you’ve made the right choice, and it will enhance your reputation for only using the best quality products
Supplied fully assembled
Fully speed controllable
Can be used in any none hazardous environment (also available for hazardous application on request)
Suitable in temperatures from -40°C to 50°C (70°C in some instances, please ask for details)
Low to high air volumes
Low to high static pressures
Available sizes 315mm – 710mm from stock
800mm – 1000mm made to order, ring for availability
1000mm + ring for availability
The Casings are spun sheet steel, then hot dipped galvanised to give a finish highly resistant to corrosion and can be mounted external and internal
The impeller (the bit that goes around and moves the air) is manufactured die cast aluminium
The motors are totally enclosed with class F insulation with protection to IP55.
Manufactured by Ziehl Abegg and distributed by Vent Axia and Systemair, this is probably the most popular short cased axial on the market today. Ziehl Abegg are one of, if not the biggest external rotor motor manufacturers in the world, they have over 100 years of engineering experience behind them, which gives you the confidence. If a low cost painted finish fan is your choice this is among the best available.
- Supplied fully assembled
- Fully speed controllable
- Can be used in any non hazardous environment
- Suitable to run in temperatures from -40°C to up to 70°C in some instances
- Low to medium air volumes
- Low to medium static pressures
- Available sizes 315mm – 630mm from stock
- 710mm – 1000mm check for availability
- Tough epoxy paint finish
- Die cast aluminium impellers (the bit that goes around)
- Motor class F insulation with protection to IP54
- All fans reversible for supply or extract
Manufactured by Ziehl Abegg and distributed by Vent Axia and Systemair, this is probably the most popular short cased axial on the market today. Ziehl Abegg are one of, if not the biggest external rotor motor manufacturers in the world, they have over 100 years of engineering experience behind them, which gives you the confidence. If a low cost painted finish fan is your choice this is among the best available.
- Supplied fully assembled
- Fully speed controllable
- Can be used in any non hazardous environment
- Suitable to run in temperatures from -40°C to up to 70°C in some instances
- Low to medium air volumes
- Low to medium static pressures
- Available sizes 315mm – 630mm from stock
- 710mm – 1000mm check for availability
- Tough epoxy paint finish
- Die cast aluminium impellers (the bit that goes around)
- Motor class F insulation with protection to IP54
- All fans reversible for supply or extract
Manufactured by Ziehl Abegg and distributed by Vent Axia and Systemair, this is probably the most popular short cased axial on the market today. Ziehl Abegg are one of, if not the biggest external rotor motor manufacturers in the world, they have over 100 years of engineering experience behind them, which gives you the confidence. If a low cost painted finish fan is your choice this is among the best available.
Supplied fully assembled
Fully speed controllable
Can be used in any non hazardous environment
Suitable to run in temperatures from -40°C to up to 70°C in some instances
Low to medium air volumes
Low to medium static pressures
Available sizes 315mm – 630mm from stock
710mm – 1000mm check for availability
Tough epoxy paint finish
Die cast aluminium impellers (the bit that goes around)
Motor class F insulation with protection to IP54
All fans reversible for supply or extract
Manufactured by Ziehl Abegg and distributed by Vent Axia and Systemair, this is probably the most popular short cased axial on the market today. Ziehl Abegg are one of, if not the biggest external rotor motor manufacturers in the world, they have over 100 years of engineering experience behind them, which gives you the confidence. If a low cost painted finish fan is your choice this is among the best available.
Supplied fully assembled
Fully speed controllable
Can be used in any non hazardous environment
Suitable to run in temperatures from -40°C to up to 70°C in some instances
Low to medium air volumes
Low to medium static pressures
Available sizes 315mm – 630mm from stock
710mm – 1000mm check for availability
Tough epoxy paint finish
Die cast aluminium impellers (the bit that goes around)
Motor class F insulation with protection to IP54
All fans reversible for supply or extract
The Flakt Woods 2102 range of low cost high quality plate mounted extract fans.
Our recommended number one plate mounted fan choice
Flakt Woods reputation for only manufacturing the highest quality products is evident with this low cost range of Plate mounted Fans. Buying this fan gives you the confidence and satisfaction that comes with over 100 years of fan engineering experience.
Supplied fully assembled
Fully speed controllable
Can be used in any non hazardous environment
Suitable in temperatures from -40°C to 50°C
Low to medium air volumes
Low to medium static pressures
Available sizes 315mm – 500mm from stock
560mm – 710mm made to order in 3 weeks
The grey coloured plate is manufactured from mild steel with a powder coat painted finish.
The impeller (the bit that goes around and moves the air) is manufactured from glass filled polypropylene and will stay intact up to temperatures of over 100°C
The motors are totally enclosed with class F insulation with protection to IP55. Single phase motors have overheat protection
The Flakt Woods 2102 range of low cost high quality plate mounted extract fans.
Our recommended number one plate mounted fan choice
Flakt Woods reputation for only manufacturing the highest quality products is evident with this low cost range of Plate mounted Fans. Buying this fan gives you the confidence and satisfaction that comes with over 100 years of fan engineering experience.
Supplied fully assembled
Fully speed controllable
Can be used in any non hazardous environment
Suitable in temperatures from -40°C to 50°C
Low to medium air volumes
Low to medium static pressures
Available sizes 315mm – 500mm from stock
560mm – 710mm made to order in 3 weeks
The grey coloured plate is manufactured from mild steel with a powder coat painted finish.
The impeller (the bit that goes around and moves the air) is manufactured from glass filled polypropylene and will stay intact up to temperatures of over 100°C
The motors are totally enclosed with class F insulation with protection to IP55. Single phase motors have overheat protection
The Flakt Woods 2102 range of low cost high quality plate mounted extract fans.
Our recommended number one plate mounted fan choice
Flakt Woods reputation for only manufacturing the highest quality products is evident with this low cost range of Plate mounted Fans. Buying this fan gives you the confidence and satisfaction that comes with over 100 years of fan engineering experience.
Supplied fully assembled
Fully speed controllable
Can be used in any non hazardous environment
Suitable in temperatures from -40°C to 50°C
Low to medium air volumes
Low to medium static pressures
Available sizes 315mm – 500mm from stock
560mm – 710mm made to order in 3 weeks
The grey coloured plate is manufactured from mild steel with a powder coat painted finish.
The impeller (the bit that goes around and moves the air) is manufactured from glass filled polypropylene and will stay intact up to temperatures of over 100°C
The motors are totally enclosed with class F insulation with protection to IP55. Single phase motors have overheat protection
The Flakt Woods JM axial flow extract fan range of cost effective highest quality long cased axials.
We think this product is the World’s best axial fan, and our recommended number one choice for every industrial and commercial application
The build quality and reliability are the highest we have ever experienced with fans still running since the range was introduced in the early 1990’s
Every time you fit this fan you know you’ve made the right choice, it will enhance your reputation for only using the best quality products
- Supplied fully assembled
- Fully speed controllable
- Can be used in any non hazardous environment (also available for hazardous application on request)
- Suitable in temperatures from -40°C to 50°C (70°C in some instances, please ask for details)
- Low to high air volumes
- Low to high static pressures
- Available sizes 315mm – 710mm from stock
- 800mm – 1000mm made to order, ring for availability
- 1000mm + check for availability
- The Casings are spun sheet steel, then hot dipped galvanised to give a finish highly resistant to corrosion and can be mounted external and internal
- The impeller (the bit that goes around and moves the air) is manufactured die cast aluminium
- The motors are totally enclosed with class F insulation with protection to IP55.
it has been replaced with a EJ411452 to make it ERP 2013 compliant (please be aware there may be a performance difference, check if in doubt)
All spare parts are still available to buy; the motor part code is BT914030
The Flakt Woods JM axial flow extract fan range of cost effective highest quality long cased axials.
We think this product is the World’s best axial fan, and our recommended number one choice for every industrial and commercial application
The build quality and reliability are the highest we have ever experienced with fans still running since the range was introduced in the early 1990’s
Every time you fit this fan you know you’ve made the right choice, it will enhance your reputation for only using the best quality products
-
Supplied fully assembled
-
Fully speed controllable
-
Can be used in any non hazardous environment (also available for hazardous application on request)
-
Suitable in temperatures from -40°C to 50°C (70°C in some instances, please ask for details)
-
Low to high air volumes
-
Low to high static pressures
-
Available sizes 315mm – 710mm from stock
-
800mm – 1000mm made to order, ring for availability
-
1000mm + check for availability
-
The Casings are spun sheet steel, then hot dipped galvanised to give a finish highly resistant to corrosion and can be mounted external and internal
-
The impeller (the bit that goes around and moves the air) is manufactured die cast aluminium
- The motors are totally enclosed with class F insulation with protection to IP55.
.
The Flakt Woods JmMax fan axial flow extract fan range of high performance and reliability 2 stage axial flow fans
This fan was introduced to satisfy ventilation systems where high pressure fans are required, where only single phase supply (240volts) is available and speed control is required
A typical application where this fan is commonly used is in the catering industry where a high level of filtration is required, usually the result of fitting odour control via Pre and Carbon Filters*
The build quality and reliability are the highest we have ever experienced, in a range of fans that are designed to work harder than most
Every time you fit this fan you know you’ve made the right choice, and it will enhance your reputation for only using the best quality products
-
Supplied fully assembled
-
Fully speed controllable
-
Can be used in any non hazardous environment
-
Suitable in temperatures from -40°C to 50°C
-
Low to high air volumes
-
Low to high static pressures
- Available sizes 315mm – 630mm from stock
The Casings are spun sheet steel, then hot dipped galvanised to give a finish highly resistant to corrosion and can be mounted externally and internally
The impeller (the bit that goes around and moves the air) is manufactured die cast aluminium
The motors are totally enclosed with class F insulation with protection to IP55.
*High pressure systems can also consist of duct size restrictions, an unusual amount of ducting including a high number of bends, other forms of filtration such as Heppa Filters or Electrostatic filters. We can check the suitability of this fan for your application if required, please contact by any means you feel comfortable with and we’ll offer free advice
-
Versions
- Downloads
The Flakt Woods JM axial flow extract fan range of cost effective highest quality long cased axials.
We think this product is the World’s best axial fan, and our recommended number one choice for every industrial and commercial application
The build quality and reliability are the highest we have ever experienced with fans still running since the range was introduced in the early 1990’s
Every time you fit this fan you know you’ve made the right choice, it will enhance your reputation for only using the best quality products
- Supplied fully assembled
- Fully speed controllable
- Can be used in any non hazardous environment (also available for hazardous application on request)
- Suitable in temperatures from -40°C to 50°C (70°C in some instances, please ask for details)
- Low to high air volumes
- Low to high static pressures
- Available sizes 315mm – 710mm from stock
- 800mm – 1000mm made to order, ring for availability
- 1000mm + check for availability
- The Casings are spun sheet steel, then hot dipped galvanised to give a finish highly resistant to corrosion and can be mounted external and internal
- The impeller (the bit that goes around and moves the air) is manufactured die cast aluminium
- The motors are totally enclosed with class F insulation with protection to IP55
The Flakt Woods JM axial flow extract fan range of cost effective highest quality long cased axials.
We think this product is the World’s best axial fan, and our recommended number one choice for every industrial and commercial application
The build quality and reliability are the highest we have ever experienced with fans still running since the range was introduced in the early 1990’s
Every time you fit this fan you know you’ve made the right choice, it will enhance your reputation for only using the best quality products
- Supplied fully assembled
- Fully speed controllable
- Can be used in any non hazardous environment (also available for hazardous application on request)
- Suitable in temperatures from -40°C to 50°C (70°C in some instances, please ask for details)
- Low to high air volumes
- Low to high static pressures
- Available sizes 315mm – 710mm from stock
- 800mm – 1000mm made to order, ring for availability
- 1000mm + check for availability
- The Casings are spun sheet steel, then hot dipped galvanised to give a finish highly resistant to corrosion and can be mounted external and internal
- The impeller (the bit that goes around and moves the air) is manufactured die cast aluminium
- The motors are totally enclosed with class F insulation with protection to IP55
Another great fan from FlaktWoods, Bifurcated Fans (sometimes shortened to Bifs or Bif Fans) are inline axial flow fans where the motor has been taken out of the airstream. This allows the fan to operate at higher temperatures.
Available sizes 152mm – 305mm from stock
The Casings are spun sheet steel, then hot dipped galvanised to give a finish highly resistant to corrosion and can be mounted external and internal
The impeller (the bit that goes around and moves the air) is aluminium silicon alloy
The motors are totally enclosed with class F insulation with protection to IP55.
The fans can be installed horizontal or vertical
They can be run upto 200Deg Continuos temperature
3ph fans only are suitable for speed control via inverter
Another great fan from FlaktWoods, Bifurcated (sometimes shortened to Bifs or Bif Fans) are inline axial flow fans where the motor has been taken out of the airstream. This allows the fan to operate at higher temperatures.
Available sizes 152mm – 305mm from stock
The Casings are spun sheet steel, then hot dipped galvanised to give a finish highly resistant to corrosion and can be mounted external and internal
The impeller (the bit that goes around and moves the air) is manufactured die cast aluminium
The motors are totally enclosed with class F insulation with protection to IP55.
The fans can be installed horizontal or vertical
They can be run upto 200Deg Continuos temperature
3ph fans only are suitable for speed control via inverter
The Flakt Woods JM axial flow extract fan range of cost effective highest quality long cased axials.
We think this product is the World’s best axial fan, and our recommended number one choice for every industrial and commercial application
The build quality and reliability are the highest we have ever experienced with fans still running since the range was introduced in the early 1990’s
Every time you fit this fan you know you’ve made the right choice, it will enhance your reputation for only using the best quality products
Supplied fully assembled
Fully speed controllable
Can be used in any non hazardous environment (also available for hazardous application on request)
Suitable in temperatures from -40°C to 50°C (70°C in some instances, please ask for details)
Low to high air volumes
Low to high static pressures
Available sizes 315mm – 710mm from stock
800mm – 1000mm made to order, ring for availability
1000mm + check for availability
The Casings are spun sheet steel, then hot dipped galvanised to give a finish highly resistant to corrosion and can be mounted external and internal
The impeller (the bit that goes around and moves the air) is manufactured die cast aluminium
The motors are totally enclosed with class F insulation with protection to IP55.
The Flakt Woods JM axial flow extract fan range of cost effective highest quality long cased axials.
We think this product is the World’s best axial fan, and our recommended number one choice for every industrial and commercial application
The build quality and reliability are the highest we have ever experienced with fans still running since the range was introduced in the early 1990’s
Every time you fit this fan you know you’ve made the right choice, it will enhance your reputation for only using the best quality products
Supplied fully assembled
Fully speed controllable
Can be used in any non hazardous environment (also available for hazardous application on request)
Suitable in temperatures from -40°C to 50°C (70°C in some instances, please ask for details)
Low to high air volumes
Low to high static pressures
Available sizes 315mm – 710mm from stock
800mm – 1000mm made to order, ring for availability
1000mm + check for availability
The Casings are spun sheet steel, then hot dipped galvanised to give a finish highly resistant to corrosion and can be mounted external and internal
The impeller (the bit that goes around and moves the air) is manufactured die cast aluminium
The motors are totally enclosed with class F insulation with protection to IP55.
The Flakt Woods JmMax fan axial flow extract fan range of high performance and reliability 2 stage axial flow fans
This fan was introduced to satisfy ventilation systems where high pressure fans are required, where only single phase supply (240volts) is available and speed control is required
A typical application where this fan is commonly used is in the catering industry where a high level of filtration is required, usually the result of fitting odour control via Pre and Carbon Filters*
The build quality and reliability are the highest we have ever experienced, in a range of fans that are designed to work harder than most
Every time you fit this fan you know you’ve made the right choice, and it will enhance your reputation for only using the best quality products
Supplied fully assembled
Fully speed controllable
Can be used in any non hazardous environment
Suitable in temperatures from -40°C to 50°C
Low to high air volumes
Low to high static pressures
Available sizes 315mm – 630mm from stock
The Casings are spun sheet steel, then hot dipped galvanised to give a finish highly resistant to corrosion and can be mounted externally and internally
The impeller (the bit that goes around and moves the air) is manufactured die cast aluminium
The motors are totally enclosed with class F insulation with protection to IP55.
*High pressure systems can also consist of duct size restrictions, an unusual amount of ducting including a high number of bends, other forms of filtration such as Heppa Filters or Electrostatic filters. We can check the suitability of this fan for your application if required, please contact by any means you feel comfortable with and we’ll offer free advice
The Flakt Woods JM axial flow extract fan range of cost effective highest quality long cased axials.
We think this product is the World’s best axial fan, and our recommended number one choice for every industrial and commercial application
The build quality and reliability are the highest we have ever experienced with fans still running since the range was introduced in the early 1990’s
Every time you fit this fan you know you’ve made the right choice, it will enhance your reputation for only using the best quality products
Supplied fully assembled
Fully speed controllable
Can be used in any non hazardous environment (also available for hazardous application on request)
Suitable in temperatures from -40°C to 50°C (70°C in some instances, please ask for details)
Low to high air volumes
Low to high static pressures
Available sizes 315mm – 710mm from stock
800mm – 1000mm made to order, ring for availability
1000mm + check for availability
The Casings are spun sheet steel, then hot dipped galvanised to give a finish highly resistant to corrosion and can be mounted external and internal
The impeller (the bit that goes around and moves the air) is manufactured die cast aluminium
The motors are totally enclosed with class F insulation with protection to IP55
The Flakt Woods JM axial flow extract fan range of cost effective highest quality long cased axials.
We think this product is the World’s best axial fan, and our recommended number one choice for every industrial and commercial application
The build quality and reliability are the highest we have ever experienced with fans still running since the range was introduced in the early 1990’s
Every time you fit this fan you know you’ve made the right choice, it will enhance your reputation for only using the best quality products
Supplied fully assembled
Fully speed controllable
Can be used in any non hazardous environment (also available for hazardous application on request)
Suitable in temperatures from -40°C to 50°C (70°C in some instances, please ask for details)
Low to high air volumes
Low to high static pressures
Available sizes 315mm – 710mm from stock
800mm – 1000mm made to order, ring for availability
1000mm + check for availability
The Casings are spun sheet steel, then hot dipped galvanised to give a finish highly resistant to corrosion and can be mounted external and internal
The impeller (the bit that goes around and moves the air) is manufactured die cast aluminium
The motors are totally enclosed with class F insulation with protection to IP55.
The Flakt Woods JM axial flow extract fan range of cost effective highest quality long cased axials.
We think this product is the World’s best axial fan, and our recommended number one choice for every industrial and commercial application
The build quality and reliability are the highest we have ever experienced with fans still running since the range was introduced in the early 1990’s
Every time you fit this fan you know you’ve made the right choice, it will enhance your reputation for only using the best quality products
Supplied fully assembled
Fully speed controllable
Can be used in any non hazardous environment (also available for hazardous application on request)
Suitable in temperatures from -40°C to 50°C (70°C in some instances, please ask for details)
Low to high air volumes
Low to high static pressures
Available sizes 315mm – 710mm from stock
800mm – 1000mm made to order, ring for availability
1000mm + check for availability
The Casings are spun sheet steel, then hot dipped galvanised to give a finish highly resistant to corrosion and can be mounted external and internal
The impeller (the bit that goes around and moves the air) is manufactured die cast aluminium
The motors are totally enclosed with class F insulation with protection to IP55.
The Flakt Woods JM axial flow extract fan range of cost effective highest quality long cased axials.
We think this product is the World’s best axial fan, and our recommended number one choice for every industrial and commercial application
The build quality and reliability are the highest we have ever experienced with fans still running since the range was introduced in the early 1990’s
Every time you fit this fan you know you’ve made the right choice, it will enhance your reputation for only using the best quality products
Supplied fully assembled
Fully speed controllable
Can be used in any non hazardous environment (also available for hazardous application on request)
Suitable in temperatures from -40°C to 50°C (70°C in some instances, please ask for details)
Low to high air volumes
Low to high static pressures
Available sizes 315mm – 710mm from stock
800mm – 1000mm made to order, ring for availability
1000mm + check for availability
The Casings are spun sheet steel, then hot dipped galvanised to give a finish highly resistant to corrosion and can be mounted external and internal
The impeller (the bit that goes around and moves the air) is manufactured die cast aluminium
The motors are totally enclosed with class F insulation with protection to IP55.
The Flakt Woods JmMax extract fan axial flow fan range of high performance and reliability 2 stage axial flow fans
This fan was introduced to satisfy ventilation systems where high pressure fans are required, where only single phase supply (240volts) is available and speed control is required
A typical application where this fan is commonly used is in the catering industry where a high level of filtration is required, usually the result of fitting odour control via Pre and Carbon Filters*
The build quality and reliability are the highest we have ever experienced, in a range of fans that are designed to work harder than most
Every time you fit this fan you know you’ve made the right choice, and it will enhance your reputation for only using the best quality products
Supplied fully assembled
Fully speed controllable
Can be used in any non hazardous environment
Suitable in temperatures from -40°C to 50°C
Low to high air volumes
Low to high static pressures
Available sizes 315mm – 630mm from stock
The Casings are spun sheet steel, then hot dipped galvanised to give a finish highly resistant to corrosion and can be mounted externally and internally
The impeller (the bit that goes around and moves the air) is manufactured die cast aluminium
The motors are totally enclosed with class F insulation with protection to IP55.
*High pressure systems can also consist of duct size restrictions, an unusual amount of ducting including a high number of bends, other forms of filtration such as Heppa Filters or Electrostatic filters. We can check the suitability of this fan for your application if required, please contact by any means you feel comfortable with and we’ll offer free advice
Another great fan from FlaktWoods, Bifurcated (sometimes shortened to Bifs or Bif Fans) are inline axial flow fans where the motor has been taken out of the airstream. This allows the fan to operate at higher temperatures.
Available sizes 400mm – 630mm from stock
800mm and 1000mm ring for availability
The Casings are spun sheet steel, then hot dipped galvanised to give a finish highly resistant to corrosion and can be mounted external and internal
The impeller (the bit that goes around and moves the air) is manufactured die cast aluminium
The motors are totally enclosed with class F insulation with protection to IP55.
The fans can be installed horizontal or vertical
They can be run upto 200Deg Continuos temperature
All suitable for speed control via inverter